B-Tech BT77 Ultragrip Pro Speaker Mount, Set of 2, Side Clamp with Tilt and Swivel, Black

I have M-Audio DSM speakers as I grabbed a pair on closeout before M-Audio stopped making them. Well, I didn't want them on my computer table as they are HUGE so I looked for the best alternative. The problem with most solution sis that they don't GRIP the speaker and I didn't want to have to worry about the speakers falling over. You see the, M-AUDIO, and I'm sure countless other speakers have rounded edges and are quite wide. The Recelco mount seemingly specked out fine but I was still in the "believe it when I see it" camp. These come with nice instructions but here are some tips: -Go to your hardware store and buy plastic anchors for these. I couldn't find a stud anywhere close to where I wanted to hang my 30 lb speakers, and the plastic studs do the job - If not using a stud buy longer screws with your plastic anchors - The clamping mechanism is tricky as it's screw based, get it fairly tight and then alternate sides until you can get it as tight as possible. - Home depot sells insulation tape that'll work instead of the stuff that comes on these to grip the speaker After installing using the above parameters this easily has held my large rounded corner speakers for over six months. I love that you can slightly angle the speakers down at yourself if you put them above ear level. These look nice with cover on them and are more than sturdy. Even without the changes I made above for most normal speakers these will work, but if you have larger weird speakers like I do take the extra moment and make the changes I did! You don't want to worry about your expensive speakers falling! Great product. BTW, I went to Tiger Direct, Best Buy and Target and couldn't find anything this good, so save yourself the time!

Installation was fairly straight forward. They include bolts and anchors for concrete but not for drywall. One one side it did not align with a stud so I had to buy some drywall achors. The only minus is though its a wall mount there is no place for cable management, so I had to mount it next to the hole where the cable comes out from my wall.

Purchased the Rocelco B-Tech Ultragrip Pro Loudspeaker Wall Mount Brackets for my NHT 1.5 bookshelf speakers. Due to the configuration of our living room and how the furniture is arranged, there was simply no room for small speaker stands and I didn't want them on the floor getting kicked around. My NHTs are 16.5"H X 25"D X 7" wide and weigh 16 lbs each. These are ultra high quality wall mounts, very heavy duty and I have no doubts they will support my speakers more than adequately. FYI, I did end up customizing my brackets somewhat with good results. Once I had my speakers mounted, I noticed they were several inches away from the wall. The mounts are obviously made for a wide range of speaker sizes and would hold much larger speakers than I have. I was able to cut a couple of inches off the bracket support post so that the distance between the wall and the back of the speakers is now only about an inch or so. It also meant I had to drill a couple of new holes in each bracket, but for my speakers, the weight is now more centered on the mounting bracket as well. My wife wasn't wild about the idea of mounting speakers on the wall, but we really didn't have any good options and these brackets look very professional. I highly recommend them if you just don't have space otherwise for medium size loudspeakers.

I used this to mount a pair of 6" bookshelf speakers up on the wall to replace my floor-tower speakers as I have a 2-year old starting to knock into things and cause general havoc! It took about the duration of an NFL game to install these, including running the wire in-wall up to the speakers. Installation was easy to follow, and the speakers are very safely secured. I am a CPA by trade and have little experience with any sort of complicated home improvement projects. My only complaint is that the cover-plate that goes over the hardware attaching it to the wall does not have a space for the speaker wire to pass through. Thus, I suppose you would either have to cut out a notch (risky because it's plastic, so doing so could crack the whole piece), or else do as I have done, which is to have them not quite fully flush with the wall. This seems like an odd oversight, since I would expect most users of the product to desire hiding the speaker wire.

J'ai cherché partout des supports muraux pour mes enceintes triangle Cométe EX (qui font déja leur poids!), aucun produit ne correspondait à ce que je voulais. Je suis tombé par hasard sur ceux ci, et je dois avouer que j'étais septique quant à la qualité au vue du prix, et bien non, au contraire, ces supports sont tout simplement excellents ! Ils inspirent confiance (et il vaut mieux vu le prix des enceintes!), pour un montage sur du ba13 attention, utiliser des chevilles molly, et si comme moi vos enceintes sont assez lourdes, renforcer le placo si possible pour éviter les mauvaises surprises! Concernant le systéme de fixation de l'enceinte, c'est très simple, l'enceinte est serrée sur les cotés (en contact avec un caoutchouc anti-dérapant)dans mon cas j'ai vissé l'arrière des hp pour assurer le montage et ainsi éviter un glissement car je les ai réglé vers l'avant. La seule amélioration que je pourrais formuler serait d'avoir un passage du cable (mais c'est vraiment un détail), j'ai percé la plaque en plastique et le tour est joué, installation digne d'un pro!! Bref si comme moi vous recherchez un support sécurisant, design, réglable dans les deux sens et adapté à quasi toutes les enceintes bibliothèque, n'hésitez pas une seconde, ce produit est le seul existant de ce type et à un prix imbattable ! Merci Amazon, délai, emballage etc au top!

If you're looking to get these mounts for your pioneers bs22: I don't recommend it. That is unless you enjoy living on the edge, or you're fine with screwing holes into your speakers. Due to how the speakers curve on the side, the clamping mechanism won't be able to clamp the whole side. What this means is that the surface area the mount is actually holding is very little, making the speakers prone to sliding off the mount if you're titling it forward. Now, if you're not going to be tilting the speakers, then you could potentially use these while having the thought that the speakers aren't 100% secure and could fall for whatever reason in the back of your mind. However, if you do choose to screw into the speakers to secure it onto the mount then the mounts are great. Its secure and it can rotate a ful 180! The only issue I can think of is that the mount requires you to essentially lock the position you want the speakers to be tilted. What I mean by this is that to be able to tilt the speakers you would have to unscrew one of the lugg nutts on the bottom, adjust the tilt of your speakers, and rescrew it(the lugg nutt is really hard to screw. You'll need a wrench. Can't unscrew by hand.), or else the speakers will just keep tilting forward due to the front heavy weight. Also friendly tip: screw the bracket in first. Next put on the bracket cover. Then start assembling the actual mount or you'll have to disassemble and reassemble it all over again. So, buy if you're ok with screwing into your speakers or if you don't mind them potentially falling. Happy mounting! Tl;dr Clamps don't clamp the whole side. Need to screw speakers onto mount for 100% secureness. Otherwise mounts are great.

This is very well made. It was intuitive and easy to assemble and mount. The fact that the skeleton of this is made of wrought iron gave me confidence that this would last long and hold up my Klipsch speakers easily and for long. Highly recommend

La instalación fue bastante sencilla, los utilicé para un par de Yamahas Hs7 y no tienen ningún problema en tolerar el peso. El ajuste es bastante cómodo y no afecta a la construcción del monitor

Cambiando mi equipo de sonido del salón, me decidí a comprar altavoces más grandes y específicos... estos ya no llevan "enganches" para colgarlos de la pared, por lo que tenía que comprar soportes. Estos están realmente bien, soportan hasta 25 kilos cada uno y sus ventajas, en mi opinión, son las siguientes: - Al atornillarlos a la pared (vienen tacos y tornillos para paredes macizas normales), llevan una tapa de forma que no se ve ni un solo tornillo. Acabado esbelto y elegante. - Se pueden girar prácticamente totalmente e incluso inclinar ligeramente arriba o abajo. - Puedes colocar una gran variedad de anchura de altavoces (consulta las especificaciones antes de comprarlos, para ver que se adapten a la anchura de tus altavoces). - Simplemente con apretar los lados, los altavoces ya se aguantan, aunque dispone de dos agujeros para atornillarlos al soporte (aunque si lo haces harás un agujero a tu altavoz lógicamente). Si los altavoces no son enormes, no hace falta atornillar. Yo compré dos packs, uno para los delanteros en los que puse unos Wharfedale Diamond 220, y en los traseros los Wharfedale Diamond 210 (más pequeños), los soportes van sobradísimos. Como comentario, el segundo pack que compré lo hice en Amazon UK (bastante más barato que en Amazon.es), desconozco como estarán los precios cuando leas esta opinión, pero por si os sirve... :)