Qty 2 OMRON D2F-01F-T Micro Switch Microswitch for Razer Logitech Apple Mouse

These were a direct replacement for the stock switches (which started double clicking) on my Razer Deathadder V2. Replacing them is for sure not easy but is in my opinion better than throwing away a $40 mouse. These switches did seem a little quieter than the stock razer switches but offer comparable tactile feedback. They do also say Japan on them.

I've had this Razer Naga Trinity for quite a few years and it just recently started giving me the double-click issue even when I only clicked once. Found these are a direct replacement microswitch. These are actually made in Japan, where the original switches are marked to be made in China. I bought two to replace both microswitches, because they were cheap enough and "why not?" After putting these new ones in, my Naga Trinity no longer had the double-click issue and it feels as if it was brand new. Instead of spending $60+ for a good mouse, I spent $6 and a little bit of time with soldering and I have a fully functioning mouse that will likely last another several years. Its worth saving money, and reducing waste

My Razer Naga started to do the dreaded double click or click and release when you are trying to hold making dragging a pain. The hardest part was getting the old ones out, once I did though I snapped these in and threw on some solder and was amazed it made my mouse like new again. Pro Tip - When I first put my moues together I had the screws snug and doing so made it so I couldn't click down on my mouse. Loosing up the mouse to a half turn or so was enough to make my mouse clicky again. My mouse has been fixed for 2 weeks now as of 1-19-2026, if these start failing prematurely I will update. For a reference my Razer was probably almost 5 years old when it started to show signs of wear, my wife has the same mouse and got it at the same time and hers started have the problem at the same time as well but hers started out much worse.

Works very well with G600. It has a softer/quieter click than the original switch, but no complaints here.

I was sick and tired of dropping 80 dollars for the nicest mouse Logitech makes (love the size etc,). So when my mouse’s left button started acting up after less than 2 years, I wanted to try and fix it. Well, it took a bit of patience and careful heating but I got the old switch out and dropped in this little beauty. It’s a little wider than the OEM switch but that didn’t matter. So far, I haven’t experienced any premature “drops” when I’m dragging or highlighting text anymore. So far so good. Tips: The battery cable connector was hard to remove. Slip a pick into the little holes and pry the connector, alternating holes until you can disconnect it. The connector is brittle but don’t worry, even with the top part of the connector gone, it can plug in securely. Buy some Logitech mouse feet when you buy this switch, you basically destroy the feet to get to the screws. Great buy!

These switches are perfect drop in replacements for my logitech G604. They even snap into place so that you dont have to hold them in while soldering. The click is noticably lighter weight than the originals. I don't mind at all, but some people might be more particular about that. Every click still feels very intentional, so its not too light.

Used these switches to replace the double clicking switches in my logitech mouse. I used these switches to replace my left and right click and the first thing I noticed is that they take very little force to actuate. This results in me accidentally clicking just by resting my fingers on the mouse buttons. To be fair, this isn't a defect but is simply a property of the switches. 2 months after installation and now the left click is starting to double click upon releasing the mouse button. Now I have to replace my switches yet again. This time I'll be using a switch with a higher actuation force.

Oddly, it works far better and more efficiently than when it was new. The button is a lot more sensitive. Be aware, if you are used to clicking a little harder due to a bad button in the past (me) this will be a hair trigger in comparison. This model has the bends in the prongs to help hold it in place. I ended up straightening them with a plier as they would not fit through the holes with the bends. No big deal. Works great, easy install (if you are good with solder and wicking).

Replaced the left button only. Slightly different feel. Works great. A much easier fix than buying a new mouse.

I needed to replace the Omron D2FC-F-7N(20M) microswitches (left and right click) in my Corsair Gaming M65 Elite RGB FPS mouse. These Omron D2F-01T-F are a perfect fit and have made my mouse feel like new, if not better. Would recommend these as a great replacement for any mouse that they'll fit in.

The model description is exact. Its made in Japan and has a T shaped terminals that is not compatible with Razer Trinity and Razer Deathadder.(height is same as the omron china one) So even if u want to purchase, go ahead and then at the time of fitting just trim the terminals a bit, then only it will fit inside the mouse. I'm not sure about Logitech and Corsair mouse, but for Razer u will have to do the above jugaad The delivery is gonna take sweet time irrespective of whether you are prime or not.

Used it as replacement for mx master 3

Is the one I need and works good.