YDmeet Shower Head Holder, Adjustable Handheld Brass Shower Head Bracket, Wall Mount Holder, Drill Free Glue Installation (Polished Chrome)

Product looks great and installed perfectly to our tile with the included manufacturer glue. My package also came with temporary adhesive paper to hold product in place, while glue dried. This worked perfectly and peeled off clean and easy after 48 hours. The included adhesive paper indicates that the company is listening to customer reviews to implement improvements, as I saw past reviews mentioning challenges in the product holding in place just after glue is applied (Problem solved by company.) The company also proactively followed up with me to be sure I received the product and was satisfied. That impressed me and prompted me to acknowledge in a review.

This replaces the crappy holder that came with the shower head. This thing is so strong and has held up for a couple years now. I would purchase it again without hesitation!

This shower head holder is well made and is all metal vs plastic used in other holders. I particularly like the tight ball joint, as I have a heavy shower head and it will hold it in place. It has to be glued on and then held in place while it dries from 48 to 72 hours. It comes with light weight adhesive strips to hold it in place while the glue it drying, but I opted to hold it in place with duct tape (see attached picture). Now I know that when I peel off the duct tape in 72 hours, the shower head holder will be solidly adhered to my wall. I also found when I screwed of the cap on the tube of glue, I could not squeeze out any glue, so I just snipped off the top. The glue is light a paste, making it easy to work with and, even though it came with two tubes of glue, I only needed to use one. Be very careful to place the glue only where the pictured instructions tell you, as putting glue in the center of the adhesive plate will lock in the rotating ball. Also only put the glue on in small dabs, as too much glue will also lock up the ball rotating ball.

Functions for intended purpose. Mechanism stiff, wound up using a different adhesive, the one included inadequate.

Works as advertised. It looks great with all the other hardware. It’s very strong. It was very easy to install. Going to buy two more.

I had the plastic mount that came with my oxygenics showerhead. I wanted to get a shorter hose, and they are easily available, nice stainless ones, but they don't fit the oxygenics holder, which is too large. All other holders, like this one, are a 'standard' size. Most holders I found have the cradle attached to the shaft at 90-degrees, which severely limits the range of motion and allows moving the showerhead in nonsensical directions. This one is angled, which means the showerhead can be adjusted to point straight or downwards. It has a nice brushed stainless finish. The ball-mount holds firm and moves smoothly. Very nicely made. It can't be tightnened, but seems like it is well made and will stay put and not sag. It is provided with a mastic adhesive, which must be cured for 48 hours. Since the plastic showerwall was not attached to the wall, I found that the adhesive is not enough, so I drilled 2 holes in the corners, and screwed into the wall. Solid. I also applied silicone around the top edge, so no water could get in to loosen the glue. Very happy.

Great quality part, adjustable to where you want to place item in shower, and hold the shower wand so functional and practical for any shower.

Overall the quality of this holder is good, seems solid. My problem was with the glue that is supposed to hold this onto my RV shower wall - I glued it and was going to leave it for a couple days, but the glue would never set up enough to keep it on the wall. The seller should provide a faster-setting glue, or possibly a construction adhesive. So, my solution was to drill holes in the base plate and screw it to the wall (as the old one was). My shower wall has wood backing behind it, so I feel the installation is solid. The swivel mechanism in this holder is very stiff, so I have no confidence glue would have ever held it for long. I would also suggest the seller pre-drill holes for those who would rather do it this way. Now that it’s installed, I’m very happy with it. Shower head fits well onto it and the satin nickle finish is very nice.

High quality product

El pegamento que trae no funciona, solo se mantuvo pegado 3 días y se cayó. El producto como tal se ve de buena calidad pero el pegamento no.

Tien très bien et belle apparence

Clean the wall surface with alcohol and follow instructions give 72 hrs for adhesive to set. Brushed nickel finish matched my Moen nickel finishes perfectly

Exactly what o ordered