2 Player Arcade Stick DIY Kit USB Encoder to PC Joystick Games + 2x 5Pin Rocker + 16x 30mm 5V LED Lit Push Button 1 + 2 Players Coin Buttons For Raspberry Pi 1 2 3 3B Mame Fighting Stick

I bought this to upgrade my Mortal Kombat II Arcade 1up cabinet I just bought used to upgrade with a PC etc. Following the many videos on Youtube made it easy and this hardware works really well. Easy to install and cable. Everything works, only mapping the keys is trickier than it could be in my opinion, but doable. Lights all work. Interestingly not all the buttons are wired the same, so you may have to swap the Red and Black on a few. I found most were red cable to the red side, but some were the other way around. This is just to get the lights working, as they are LED and require the polarity to be correct. Very happy with the end result. Enough buttons to allow you to choose colours of buttons and I added a couple as suggested by Youtubers, and there are enough in this kit to allow you to do it. I had a small issue and contacted the seller through Amazon. They responded immediately with good solid advice which sorted my very small issue. Nice to get such a product and service from China.

So far, so very good. I'm back to the 80's and my childhood dream of owning proper arcade machines like those from Big. Well, instead of course nowadays we can do it with a Raspberry pie running Retropie. I bought this set of two player buttons and have built a test assembly to try out one of the sets and I have to say I'm very impressed with the results. It's a proper retro feel to the joystick and buttons, they illuminate nicely thanks to an LED backlight. I powered one set off of the Raspberry Pie with no issues, and Retropie detected the controller board with no problems. Can't say much about longevity or wear and tear yet as I've only just got it setup. Cables are all good quality, and the microswitches rotate out of the housings easy enough. Be advised that you remove the microswitches in order to mount the buttons in place and you're likely to put some of them or all of them in the 'wrong way round' which simply means the LED will not light in this orientation. As the instructions say, just swap the power lines round and you're back up and running.

The buttons and joysticks work well, but half my LEDs weren't working, unfortunately. You get spares but not enough to replace them all. Still, my boy was thrilled with his bartop arcade build so I am happy overall. I can replace the broken LEDs later. Easy to install.

Feel quite cheap, also several lights didn’t work which turned out to be that they were wired up incorrectly so all i had to do was switch the red and black wires. About 20% of them had this problem but all working now. I don’t advise it but you can work on them ‘live’ plugged into a battery bank so you can test them before committing to plugging them in. As for the cheap feeling, they kinda squeek and the stick ball feels light and seems to be made in two parts so you can feel the seam

I bought when converting a 1up Arcade cabinet, they work really well and were pretty easy to set up. They look very good when all lit up in the dark. I'd recommend them.

Installed on an Ikea Lack table (with a Raspberry Pi 3, an old, 2nd hand, €10 monitor and a set of cheap speakers). Works like a charm. The joysticks are durable and strong, the backlit buttons are great (and there are spare lights too). Instructions are clear and easy. Just one note for installation: Make sure the 2 joysticks orientation (up-down/left-right) is aligned. I love it.

Brought this set for my arcade cabinet and plugged it all in to find that some of the lights for the buttons does not work which is very frustrating. If anyone knows how to fix this, please comment

Really pleasantly surprised at the quality offered for the price. The sticks are almost identical to my sanwa sticks and the square gate piece actually says sanwa on mine. Buttons are nice and clicky with replaceable bulbs and micro switches included in the box. Microswitches seem to be really good quality on the stick and buttons