Dremel High Performance Rotary Tool Kit with 30 Accessories 4000-2-30

Je recommande! Seul petit bemol, je n'avais pas vu en fait que ce dremmel avait besoin d'un transfo. Satisfait cependant

Muy buena calidad, funciona perfectamente y sin problema de empaquetado.

Leider kam das Produkt schon defekt bei mir an. Ich bin sehr enttäuscht, da ich von einer Firma wie dieser so einen Schrott nicht erwartet habe. Völlig unbrauchbar. Schade.

GET THIS DREMEL (with Prime shipping) I damaged my 7 year-old Dremel and had to replace it. Over the course of 7 years, I used my Dremel every week to grind my dogs' nails. One dog has soft nails and the other's nails are dense. I got my puppy 7 years ago and got a second dog 5 years ago. I tried one of the grinders marketed for doing dog nails and those are crap. Over 7 years, I ground down 2 sets of pug toenails every week. I also used my Dremel to remove a section of baseboard for bookshelf installation. So I can't comment on many of the uses for a Dremel. When it was time to replace it, I looked for a version with a separate on/off switch from the speed knob. I also wanted one that was at least 30,000 RPM. That led to the Dremel 4000. I didn't need the case and really only needed one sanding accessory, but that's not an option. DON'T BUY THE UBANTE - While searching for the Dremel 4000, I noticed the cost started at $75, and that there was an UBANTE U300 with variable speed from 10,000 to 37,000 RPM. It had good reviews (4 1/2 stars and quite a few reviews). Since I use it for only one thing (dog nails), I thought it would be fine. It was not. The sanding head was either way too rough or way too smooth, and didn't even fit snugly on any of the shafts. When I ground the dogs' nails, the rotary tool slowed down and jerked when I touched their nails. It couldn't maintain its speed. It also ran very hot. My poor dogs, which are perfectly calm for nail trimmings kept jerking and trying to get away. After 2 uses, the entire casing began vibrating enough to make my hand go numb. I'm throwing this unit away. I'm not even going to insult someone by giving them this. I have no idea how this garbage got a 4-star rating. BUY WITH PRIME SHIPPING - I immediately ordered a Dremel 4000. There were 2 options - with Prime for $75, and Free shipping and one-week delivery for $45 from VMInnovations. I could wait a week to trim my dogs' nails. So I ordered the Dremel 4000 with free shipping. The order information told me that the item would arrive in 4-8 days. The same day that I ordered it, the seller indicated that the item was on its way to the carrier. Yay! I was hopeful that it would arrive in 4 days. On the 4th day, the tracking indicated that the item was on its way to the carrier. There was no change on the 8th day, but the order info told me the item would arrive that day! I didn't have a package when I got home from work and I checked the app. The information had not changed. At 8pm, I checked it again. This time, it told me that my package was late, and that if I didn't receive it by Saturday (day 13) that I should contact Amazon support. At that point, I ordered this Dremel 4000 for $75 with Prime Shipping. It arrived 2 1/2 days later (on day 11) and I still haven't received the VMInnovations order. As soon as I receive it, I'm returning it. ABOUT THIS DREMEL - As soon as I got this Prime order in a timely fashion, I opened it, set it up, and used it. It was a little tricky to figure out how to put on the sanding tip that I wanted. I understood how to put the metal tip in the shaft. I've used a drill before - You hold down the button and unscrew the metal piece to open the inside of the tip. Then you put the metal "bit" or whatever inside it, hold down the button and tighten the piece back. The wrench helped. What took me a few minutes was figuring out how to swap the rough grit sanding circle with the medium grit one. Basically, use the handle of the provided wrench as a screwdriver in the end of the sanding tip. There's a little screw there. When you loosen the screw, the sanding hoop piece gets loose. Swap them and tighten it. I then used it for my dogs' nails and was super-duper happy. It worked wonderfully. The nails were done quickly and with no nervous dogs. The Dremel ran smoothly and the air that blew the nail dust seemed better on this one. I also like the separate power/speed controls. It allows me to leave it on the same speed every time. USING THIS FOR DOG NAILS - I use a variable speed setting of 22 and the medium sanding tip. This works for both of my dogs: one with dense nails that grow slowly and the other has softer nalis that grow quickly. I sit on the sofa with my feet on a stool, and lay each dog (Pug) on their back with their head away from me. They've been doing it for years, and are perfectly calm. Plus I always give them a treat afterwards. If you're new to trimming dog nails, make sure you check YouTube or something to learn how to do it. Dremels are great because they don't leave the sharp edges like clippers, and if you do accidentally cut the nails too short, they don't bleed as long.

Es conocido que Dremel es una excelente opción en herramientas rotativas, nunca había usado una, pero tengo experiencia con taladros y herramientas rotativas de otras marcas más económicas y de mejor calidad. Comparando me doy cuenta de que no hay nada qué pensar, la demel es superior en todos los aspectos. La 4000 es la mejor opción, por su versatilidad y potencia. Todas las cosas que quise hacer con una multiherramienta son posibles con la Dremel, cosa que no lograba con otras, por frenarse, calentarse, o simplemente funcionar mal. Todas las funciones que ofrece las cumple a un nivel de perfección. No vale la pena decidir entre una económica o una inversión duradera, la mejor opción es esta marca.