1.9" Beadlock Wheels Rims

Awesome looking wheels for retro look with 2 caviats, the 20 tiny screws that are purely decorative for each wheel, non-ferrous so be prepared for some possible aggravation, and they're definitely snug on the hubs to extent you could probably lose the nut without losing the wheel, but the OEM wheels were pretty snug too. All in all though, great looking wheels and just what I needed for my K5

High quality. Easy to put together. Exquisite details. Secure packaging. Fast shipper. Have purchased multiple items from seller. Will purchase again in near future.

Went together easily and look great. Add some weight also. The center caps just set them apart in my opinion.

These wheels certainly look fantastic, and they go together pretty well. The outer ring of decorative screws takes a while to install- I'd recommend a tiny amount of blue loctite on each screw, and tighten it until it's just snug. If you wrench down on it, you'll either strip the threads out or snap the tiny bolt head. They're decorative, so they don't need to be that tight. These come with 3 different bolt sizes. The smallest bolts are the decorative ones, the middle size is for the wheel hub cover, and the largest size is for the beadlock ring in the rear. You get one extra bolt of each size with each wheel, so four spares of each size in total. As far as aluminum wheels go, these have a good amount of weight to them. There's a good chance your set may arrive with a handful of scratches and little scuffs. This may bother some people, but the way I drive my RC, I'm bound to add more damage so it doesn't bother me. The wheels come with 5-bolt center caps that cover the axle nut, and every single one has a faux locking hub machined into the top. I took a paint marker and painted the front "lockers" red, which really set off the look. Overall, decent value for the money (especially considering the wheels that these are cloning cost over $100 for a set of four). I can't wait to see how they do on the trail!

Mounted proline bfg all terrains on these easily Scx10iii Great scale wheel that matches what's on my real truck. Centerlines from back in the day

I put these on a trx4 79 bronco. They are similar to the stock wheels so they are a great match. Very nicely machined. Some reviews mention the small screws breaking but that's most likely due to over torque on these tiny screws so what else can you expect. There are 20 decorative screws on each wheel. Very nice and would recommend

Very nicely machined wheels and great quailty. Bought them to put on a TRX4 F150 due to them being very similar to the stock plastic non-beadlock wheels and the original wheels found on older Ford trucks. The stock hub caps that thread onto the axle fit with these wheels perfect. The more common brass rings found on Amazon do not fit these wheels but I used Injora silicone inserts and the combo with Injora tires are.more than double the weight of stock plastic wheels with Canyon tires. Definitely recommend

These wheels are stunning and an absolute bargain. I liked them so much I just bought a second set! I did not have any issues with the decorative screws. The holes were all fully tapped and the screws went in all the way and were snugged down fully by hand. Due to the very fine thread pitch I did not use loctite, its just not needed. The stock VXT tires that came with my VS4-10 Pro beaded up perfect with these rims. The second set is going to be used on a set of Pitbull Rock Beast XLs. These are great looking wheels…just use some care when installing the decorative screws (ie. do not use a drill, don't torque em down like your life depends on it) and I think you'll be happy with them.

TBH was worried about holes not being tapped and soft screws. Not the case here. Every hole was tapped. The screws tiny screws being soft is not an issue as they are decorative, not functional. I recommend using a bit of loctite on the tiny perimeter screws. Loctite isn’t needed on the beadlock ring. And it’s your choice on the center cap. These are an excellent option flex for the TRX-4 Bronco as these wheels maintain the stock look, however you may want to buy option TRX-4 hex adapters that are a bit wider than stock.

I don't know if the other reviewers received a bad batch, but my little outer ring screws were just fine. A LOT to lock tight and put in though. I have large brass portal weights in the front of my Trx4, and had to take a Dremel to the outer edge of the portal weights to clear the inner hardware of these beadlocks. I'm impressed by these wheels! Excellent quality and they include a few extra screws just in case.

These are amazing! I Read that some guys are complaining about the little bolts. Don’t listen. You just need patience and the right Allen key, and they go in nicely. Honestly these are easy to bolt on and the quality it’s great. I’m getting more!!!!!

they fit my trx4 great, i put off brand tires on them so i dont know how proline tires fit , there is a ton of tiny screws to put in but other than that i am very happy.

Second set of these rims I bought just so I have another set in case you can't get them anymore in time