FlightAware Pro Stick® USB ADS-B Receiver

This is a gem if you want to decode ADSB signals. FlightAware has taken a R820T2 and added a LNA (low noise amplifier) in one slim trim USB package. This unit is capable of working with software such as SDR# and can be used to listen to FM radio stations etc. Since many folks will be using this to feed data to FlightAwares website they are selling these near cost and have designed them to work best as an ADSB receiver. You have many options you can use. FlightAware has its own software that you can install on a SDHC memory stick and be up and running within minutes. You can also choose to feed Flightradar24, PlaneFinder or the ADSB Exchange. There are also similar builds you can download and install and be up and running on your Pi in a few minutes. The best solution is likely to run the software for the ADS-B Receiver Project made by jprochazka. This of course takes a little longer to set up and asks more questions but the install script is really polished and runs well. It also uses a more advanced and tweak able demodulator. The easiest way to get going with the ADS-B Receiver Project is to use a freshly formatted SDHC card. Download NOOBS and install a fresh copy of Debian. Update the build using the sudo apt-get update & sudo apt-get upgrade commands. Once you have this you can go ahead and install the ADS-B Receiver Project. If you make a mistake or it doesn't work you can re install NOOBS and start from scratch with not too much of a hassle. The ADS-B Receiver Project will give you more stats on signal strength, CPU usage, memory usage, max distance, etc. Others have mentioned the lack of a temperature controlled crystal. Since ADS-B is a digital form of modulation that uses 2MHZ bandwidth being a little off in either direction wont affect your signal. If you are someone who likes to tweak you can adjust the PPM center it. Once the device warms up it doesnt seem to vary too much and I have mine in a uninsulated garage attic.

I have owned the standard RTL-SDR and used it for a Pi-Aware station prior to purchasing this. Without digging into stats for proof, my subjective look at the live data says that they are about the same, although the preamp built into this one might give it a slight edge. I rate the FlightAware Pro Stick a 5 star SDR, because it has an SMA connector, and is about $5 cheaper than the RTL-SDR which makes it a no-brainer purchase. Combine it with a Raspberri Pi, a 1090MHz band-pass filter, and an antenna and you have a ridiculously easy to make ADS-B receiving station. Band Pass Filter: ADS-B 1090MHz Band-pass SMA Filter Antenna: Build one or buy one: 1090MHz ADS-B Antenna - 66cm / 26in Optionally you might consider a lightning arrestor if mounting outdoors, antenna fee line, and a USB extension cable. ----------- Pros: *Cheap *Works Great *SMA port Cons: *None Bottom Line: Buy this unless you want to spring for an Airspy or something in that higher-priced category.

I received this yesterday and swapped in in place of the un-amped SDR that I had been using. I also changed out the feed line to regular coax in stead of running a long USB like I had been to keep the SDR close to the antenna. Without any other adjustments I turned the server back on, and instantly noticed a difference. Old radio was seeing just 6 ADS-B targets and 8 Mode-S. Keep in mind the antenna is just in the attic for now until I can mount it outside. New radio: 30+ ADS-B, and 20+ Mode-S, and distance increased by almost double for consistent hits. The difference is truly incredible. I did notice installing it that with the feed point being SMA and not having a swivel connection like the older ones there is a lot of weight on the end of the device. I plan to buy a few more for a project and will be buying short USB headers as well to allow flexibility and take the strain off the built-in USB connector. I am impressed with this little device though.

Good product. Performs well. If all you want is to decode airplane spots, this device suits that purpose exactly! There is a lot of chatter in the online forums about how to maximize your reception using this dongle, adding an external filter, or maybe swapping out this device for the FlightAware model that has a built in filter. I DO NOT recommend adding an external filter to this device. The price difference between adding an external filter to this device, and picking up the FlightAware model with the filter built in is really trivial ($4 at time of writing). Additionally, adding a filter prevents you from utlizing this device for other things - like experimenting with Software Defined Radio (SDR), or using it as a police or fire scanner, an airplane communications receiver, Amateur (ham) Radio receiver, and the like. If you get this model, it will perform well, and will let you experiment with SDR, which can be just as much fun as airplane tracking. Regardless of whether or not you want to experiment later with this device, it does an excellent job decoding airplane spots. It's good quality, and will perform well. And all the debate on the online forums about needing a filter or not needing a filter won't matter - your need for a filter will largely depend upon the quality of your antenna and feedline, as well as the amount of RF interference in your area. So no one else's experiences with their location will help you with yours. You're just going to have to try it, and find out for yourself. Again, if you're already thinking about buying an external filter for this unit, why not just add 4 bucks and get one of these WITHOUT a filter, and one WITH? Then you'll have the benefits of both worlds!? And have a "leftover" SDR dongle to play with!?

I am not normally one to write reviews, but this thing is quite amazing. Instantly had an increase in range and in number of positions per second. Messages per second nearly doubled, and the range increased anywhere from 10-30% (depending on the direction). Using a third party high gain antenna, the flightaware filter, (which I installed about a month ago, and also provided about a 10-15% boost), and about 50 feet of LMR 400 cable. Very impressed so far, just installed, so these are preliminary results, but the early results are looking promising. Furthest distance seen in the first hour of operation was 240 miles (but not consistently), with the average consistent distance being about 190 miles!

Well I ended up getting the blue receiver which has the built in filter because Amazon must have applied the wrong label. I won’t complain about a free upgrade! But to my knowledge, the difference between the two is the filter. It’s very reliable but the only thing is that it feels a little loose in the USB port. If you’re using this with a Raspberry Pi, it blocks EVERY USB port. I have a Logitech keyboard and the dongle wouldn’t fit with the ADSB receiver plugged in which means that in order to manage my Pi, I have to use VNC which is what I’d recommend anyways.

Over the past week, I've been running tests on a Piaware station I built for remote mounting. Power over Ethernet to a Raspberry Pi 3B+, mounted in a water-resistant "cable TV" box attached the the pole with the antenna on top, and only a 1 meter cable to the radios. This station used Nano2 radios, and saw about 40% as much traffic as my "reference" station 20 feet away, which uses an Orange Pro Stick. Today, I swapped out the 1090 MHz Nano for an Orange Pro Stick. The range JUMPED. The test station now hears MORE stations than my reference station, attributable to having a 1 meter feed line instead of 10 meters. The tuned pre-amp in the FA radio makes a HUGE difference. I'm in an area where the filtering of the Blue Pro Stick might make a difference (multiple cell towers within a kilometer of the antenna), so maybe I'll play with adding a filter later. This is working well enough now that the Nano2 has been swapped out that I may just leave it alone.

The technology to track planes and to show them on a map has always been interesting to me. I've been a Flight Radar 24 and Flight Aware fan for many years, and I'm not an electrical engineer so I wasn't sure how to setup a flight receiver. The technology to track planes and to show them on a map has always been interesting to me. I've also wanted to get a Raspberry Pi to play with, but never found that "killer" app to motivate me to buy one. This new FlightAware Pro stick USB receiver, changed all that. This is really incredible!! I went to the FlightAware Piaware website to get the shopping list of items to buy. Went to Amazon and bought the Raspberry Pi, case, SD card, power supply and Pro stick, followed the detailed instructions and was up and running in a couple of hours, sending my data to the FlightAware site. At first I was only picking up very close signals, so I purchased and added on WiFi and an antenna with an extension cable to install on the roof of my back deck about 15 feet above ground. Even though I don't have full line of sight in all directions, I am picking up signals up to 150 miles away. This is a very cost effective way (less than $150 total) to be a part of the FlightAware network. My biggest problem was convincing my wife to let me install the small antenna on the back of the house.

Increased my positions received by about 30% compared to the generic R802T dongle I was using previously. Range increased slightly as well. Good value for the price and works better than the generic dongles.

Brilliant FlightAware Pro USB Stick receiver and built in preamp, works well with Raspberry Pi 3b, FlightAware 1090MHz Antenna, FlightAware 1090MHz Band-bass filter and N Male Connector to SMA Male Connector (2 metre length) cable. Alternatively this receiver also works well with a Comet Tri-Band 145/433/1200Mhz GP-95N base antenna as long as the 1090 MHz band-pass filter is used. Even with mountains on three sizes I am receiving over 65,000 data report signals daily at distances of 50 to 200 miles away. I would recommend this receiver for a beginner and professional too. Installed and running on the Raspberry Pi 3b and left to run on its own for months.

La ricezione nella gamma 1090Mhz è superiore ad altri dongle, il connettore SMA elimina la necessità di adattatori, la ricezione aumenta ed è più selettivo. Apparentemente non ci sono circuiti diversi dalle chiavette standard, ma è comunque migliore. Essendo il case un pò più largo, si perde la possibilità di usare la porta usb di fianco (es. Raspberry, ma non solo). Costo adeguato, peccato che non sono incluse le spese di spedizione. Complessivamente un buon prodotto.

Ich erlaube mir einen etwas ausführlicheren Erfahrungsbericht ….. ohne Ingenieurs Wissen und ohne Messgeräte. Ich poste meine Beobachtungen jeweils bei allen Produkten. Für das Flight Tracking bei Flightradar24 habe ich mir einen Raspberry Pi3 gekauft. Für meine ersten Tests habe ich mir den NooElec NESDR Mini 2+ Stick inkl. Antenne gekauft. Nach einer einfachen Installation (keine Treiber, keine Anpassungen, einfach einstecken) war ich überrascht, wie viele Flugzeuge aus dem Dachgeschoss trotz eingeschränkter Sicht zu sehen waren. Der Stick ist wirklich gut und für eine günstige «all-in-one» Lösung genau das Richtige. In einem weiteren Schritt habe ich mir dann den FlightAware Pro Stick, den ADS-B 1090MHz SMA Filter und die 1090MHz ADS-B 66cm Antenne gekauft. Die passenden Kabel waren nicht einfach zu finden, denn SMA ist nicht gleich SMA Stecker, zu beachten gilt, ob im Stecker der Stift drin ist oder nicht (Reverse oder nicht). Die Antenne ist wohl eines der wichtigsten Elemente und hat mir den ersten grossen Schub der Reichweitenvergrösserung gebracht. Unter dem Motto «so hoch wie möglich, am besten auf dem Dach» fand die Antenne schliesslich auch ihren Platz. ABER: Das Antenne-Kabel ist hier das zweitwichtigste Element – ein verlustarmes Kabel ist von Bedeutung, denn bei 8 Meter Kabellänge geht so einiges an Signalen verloren. Erstaunt war ich über den Stick, der ohne Filter eine Verschlechterung gegenüber der ersten Variante gebracht hat. FlightAware Stick ohne Filter bringt nichts, zumindest bei mir! Meine Antenne hat noch nicht den höchsten Punkt des Daches erreicht, eine Versetzung der Antenne ist geplant. Mit der aktuellen Platzierung (210 Grand Sicht) tracke ich pro Tag ca. 2'400 Flugbewegungen mit einer Reichweite bis ca. 150 nm – Ausreisser bis über 300 nm gibt es zwischendurch. Fazit: Für Einsteiger ist die NooElec 2+ Lösung perfekt, wer es gerne fix hat und auf Reichweite aus ist, dem kann ich nur das Trio «Stick, Filter und Antenne» empfehlen. Und nicht vergessen: Das richtige Antennenkabel mit den richtigen Stecker. Viel Spass wünscht GaRoMeSi

conçue par l'agrégateur de flux ADS-B du même nom, elle est vendue à prix coutant, ce qui est un exploit. L'objectif étant d'augmenter la couverture de son réseau... à notre que cette clef inclue un ampli interne très efficace qui permet environ 40% de réception en plus par rapport à une clef d'entrée de gamme. Regardez aussi l'antenne du même fabricant!