10-Pack 3.28FT 16X16MM LED Strip Channel Diffuser V Shape

PERFECT!!! for its price point and quality.

My mother in law has a old house that had poor lighting going into the basement. She asked someone to put in some lights, they strung up some work lights. These were glaring and looked horrible. I rarely have to go into her basement, but the few times I did, these work lights were right in my face. Something had to be done. So I ordered an LED light strip and these aluminum tracks and diffusers. I only ended up using 3 of the tracks and cut the LED to size. This turned out fantastic in her cellar way. They are really easy to install and the diffuser just snaps in place. Well worth the price and time to install. Yes, the wall and ceiling still need work, but that can wait.

Great quality and all the essential hardware provided. Excellent deal

I’m gonna say you’ll prolly want an old school hand miter box for cutting corners. Shipped in a overly large Amazon Shipping box, product was tightly packed in its own white/brown box no frills IIRC. Came with instructions, I didn’t use them. I used a power miter-saw with a metal cutting blade. I spent more time cleaning the cut after using a power tool, than I did installing it. The metal cutoff disk melted the aluminum leaving me to hand file and sand down cuts. This is why I recommend a miter box and a hacksaw. Hacksaws would cut thru this Aluminum quickly and cleanly. The pack does have elbows for corners but my package came with 2 per purchase. I’d need quite a few more to complete my kitchen. These would greatly simplify corners and would only require a 90* cut to fit. I went for 45* cuts on corners and later realized the Philips Hue tape does not bend well in corners. The plastic diffusers that protects the lights can but with my light strip it does not work with 90* bend. I had to leave a gap at the corners as a remedy. Since I couldn’t get a 6pin Philips Hue to lay down in the corners perfectly, you might have luck with other tapes. It still looks really good and prolly a better install than my builder would have completed. So about product. The channel the light strip lays in is decently wide and accommodates 6 pin strips RGB lights. The product comes with brackets to hang the channels but I used a strong adhesive, I don’t plan to remove the channels once I installed them. The channel puts the light in the right places. The milky light diffuser does an excellent job of evenly projecting light. The diffuser once installed looks like a semi glossy quarter round under the kitchen cabinets. Overall the finished product looks remarkable, I believe I did a better job than my builder would have completed and for less money. I’d recommend this and thanks for reading

The basic aluminum channels and diffuser were quite satisfactory. However for my use case; a platform bed frame, I really could have used plastic OUTSIDE corner joining pieces. The kit comes with two plastic INSIDE corner connectors which were of no use. The kit also does not include any connectors for use between the channels other than the metal hanging clips. The plastic end caps come with either a hole for the LED strip light cable to pass through or no hole. However I could not use the pass through end caps unless I desoldered the cable from the LED strip which I did not want to risk doing. A two piece end cap would solve this problem. I did use COB type LED strip lights and diffuser was able to project a continous light without dark spots between the LEDs.

Works well and looks good. Good for living rooms where your company will see. I like the lights undifused in the bedroom though. It’s more challenging than I expected to get them lined up and it bugs if you have to truncate one of them. I used an angle grinder saw and it was a difficult process that didn’t work out so great. Pieces were either shredded or bent off at the ends.

I used these in my camper. Easy to cut with a hacksaw and a miter box. Added a nice touch to the old camper.

We gutted and replaced our kitchen. We wanted under counter lights that were as invisible as possible. This set of light strip channels and diffusers is exactly what we wanted. I mounted these under the rear of the cabinet within the lower trim. Because it was new construction wiring was a cinch and I soldered all connections. The aluminum channels can be trimmed to fit using a multitool or hacksaw. I cut the diffusers with a utility knife. There's plenty of hardware here for just about any project. I used cool white 4000k LED strips and it throws plenty of light. Great value and rock solid product.

some of the pieces were missing when I first received the order. I contacted the seller and he rectified the situation immediately and also offered advice and support on installation. the channel is is good quality and easy to install.

Great product! Our kitchen installer did a crude and ugly job with the undercabinet lighting. He just used the old style widely spaced LED strip and just stuck the tape to the underside of the cabinets. (see Before pic) I replaced it with COB 480 LED/m tape mounted in these diffusers and what a difference. They look beautiful and custom manufactured. The diffused light is continuous with no hot spots. The channels and diffusers cut easily with a power miter saw. I wrapped the channel and diffuser with masking tape at the cutting point, and cut it slowly. I mitered the joints at 45 deg rather than using the supplied corner pieces. I didn't have room for the mounting clips, so I drilled holes in the channel and used double sided tape and screws to mount.

妻の作業場の間接照明用に、LEDテープを保護するために購入。 ノコで切ったりしましたが、しっかりした作りで耐久もバッチリです。

Buen producto es lo que se publica

到着が海外からで到着がかかりすぎる。 実際作業が出来なかった、 それに加えて部品の欠品でさらに届くのに一か月近く掛かりました。 とりあえず有る物だけで作業しました、 取り付け後きれいに見えます、 LED点灯は直にテープ貼るより暗くなります、 つぶつぶ感は無く良い感じです。 リモコンで光量調節出来るので好みに光ります、 カバー有ると見た目すっきりします。 まだ５ｍのアングルは他の部屋に取り付け予定。