HiLetgo Digital Multimeter AC 80-260V 100A PZEM-061 LCD Display Digital Current Voltage Power Energy Multimeter Ammeter Voltmeter with Current Transformer CT

I purchased several dc inline meters, this one works more accurate than 60V/100-200A DC inline meter. Easy to use, built-in Shunt 20A is enough for Solar panel test. I haven't try to max it out but so far so good at low current. Based on seller spec is correct working voltage is 8-100V. I lower it down to 6V, the meter won't display. LED is bright enough and only pulling 0.10W. Please note this Shunt load on Positive + instead of most of watt meter using shunt on Negative- which is fine. It saves last energy state, when you turn it off/on blue led display is blinking to show last state energy. To clear it, while it blinking press and hold (very long) until you see CLR then release button and short press again to clear out last saved energy. Note: if you press not long enough it will bring you to alarm mode setting for Voltage and Amperage limiting. I make solar connectors and screw them in follow DC input (from your solar or DC power supply) and load to your electronic load device. Very straightforward. I suggest using 14AWG wires is best fit for screw terminal. Will buy more of this version than the other 60/100-200A DC inline meter is so inaccurate than this. Hope that helps

Easy to install, but instructions are lacking. ButGoogle works great for instructions.

Easy to set up. I noted that there was no reading when I first connected my solar cell as the input, but as soon as I connected the load (the battery), it took off and started counting the watts in, amps in, and accumulated watt-hours since reset...along with the voltage. Very handy little meter for solar testing under 20a, but note that the terminal connections are too small for my normal 10awg wires. I found a pair of SAE cords to use with 12 ga wires and they fit perfectly. After all, this built-in shunt is only rated for 20a. I just prefer to use 10awg for my permanent PV connections. Seems a fair price for such a useful meter.

It has 4 full digits for the voltage, and yes its within the 1% cal limit, but two digits from the resolution. wish they would have added a calibration pot. Current is spot on.

The item came fast and well packaged, and it's bigger that I thought it would be (which is good as most of it is a display). The input and output is clearly marked on the back of the unit, as well as in the manual. There is a single button which is used to turn the backlight (it's blue by the way) on and off, as well as to reset the unit (as it keeps the energy counter even if turned off). I have tested in with voltages from 5 to 20 V and with currents from 0 to about 2A. Both the voltmeter and the ampermeter are quite precise, compared to other measurement tools I have and trust: the voltage is within 0.05V, and the current is within 0.001A as far as I can see. Measurements change every second or so, which is less frequent than your average multimeter. The screen is well readable from left, right, and down sides, but less so from the up side that is usually the case with liquid crystal displays, so take that into accounting when you mount it. One other remark is, the description says the lowest voltage is 6.5V, which is true except the backlight only comes in from about 7V, so I would say if you're going to need a backlight, consider the lowest voltage at say 7.5V to be on the safe side. Now, the upper limits are 100V and 20A as per description and documentation, unfortunately I don't have equipment to push the device to its limits. Finally, I have tested the alarm function and it works fine. You can set the two voltage thresholds (upper and lower), and if the voltage is not within the range specifies, both display and backlight flashes rapidly. This might come handy if say you need to prevent your lithium battery from discharging too much (i.e. undervoltage). I am giving it five stars overall, but especially for its precision.