GINTOOYUN USB 3.0 Header Extension Cable,USB 3.0 19/20 Pin Male to Female Internal Extension Adapter(5.9 inch)

I got this header extension because I wanted to throw a better video card in my old EliteDesk 800 G1 Tower from HP. I also had to get an adapter (also on Amazon) to allow for an aftermarket power supply. The USB 3 header on my mainboard was right in-line with where my (long) graphics card would sit in the case and the default USB header stuck up way too high. This header was able to flex just enough that it fit under the graphics card perfectly. It definitely saved the day.

I have a new MSI X870E Tomahawk motherboard and the USB 3.0 header pins were too fat to accept the USB cable from my case. I purchased this extension in the hopes that the connector will fit the motherboard's USB header. It was a tight fit, but it worked.

Does exactly what I need it to do, gets the bulky USB 3 cable out of the way of my side mounted 360 Rad, BUT the motherboard connector on this is very loose, but the contact pins themselves seem to make good contact. So i applied a few dabs of hot glue to hold the connector in place and it's not moving. Just beware you might have to secure the connector or it will move and unplug itself.

Built a new pc on a 10 year old PC ATX case. Apparently these USB 3.0 plugs are now sideways rather than facing up on the motherboard, was surprised when I couldn't plug in my case's USB 3.0 plug. This adapter did the trick, looks sturdy too.

Worked perfect for my needs. Had to relocate the bulky plug off the motherboard, since it was preventing me from side intake mounting a 360mm Corsair aio in a lian li 011 Dynamic (o.g. version). Zero issues with the coming loose at connector concerns. Takes moderate tugging for them to break free. In all honesty though, even if that was the case I'd probably just wrap some electrical tape around the connectors and call it a day simply because it solved my issue so easily. Its not like this pc is moved ever outside of cleaning it.

It worked for what I needed. For about a week. Then I started having issues with USB drives disappearing. The connection to the MB is so loose that it unplugs itself. There was plenty of slack in the cable to it wasn't under any stress. Its just a little too loose. Would have been an easy 5 stars but for that.

This purchase saved me. Building my friend’s PC case, his motherboard USB cable was located at the bottom near the fans and was a tight squeeze as I didn’t want to crimp any wires. While the connection is not as tight as the standard cable, it does ensure you don’t rip your pins out from trying to remove it.

Used in a pc with the graphics card covering the USB 3 connector, I was able to plug this in and have the graphics card installed

Small form factor build, and my CPU cooler's radiator and fan were blocking the front panel USB header on my motherboard. This extension is very low profile, allowing the wire to bend immediately out of the header, solving my clearance issue. Multiple reports of it being loose gave me pause while ordering, but it seems to fit perfectly snugly (as any other connector) into my Gigabyte motherboard. I've just installed and not yet long term tested, but USB devices show up, and I will update if I have any problems.

The ribbon itself was flexible. Only concern was that the connector that plugs into the motherboard had little friction. This made it so that it came loose very easily and I had to limit where I can position it, or how much I could bend it because it kept falling out of the 3.0 headers on the motherboard.

Used to move large rigid US-B3 cable header from the edge of motherboards to behind the board and out of the way. The USB3 plugs and cables are very heavily built, so often come unplugged or put board header at risk from clumsy users (aka; me). The two flat cables on this product which make up the extension are the same length, so bend unevenly (not a design choice, a requirement for bidirectional use) but splitting them into sets of two make them much more flexible for 180 degree bends. DO NOT USE a sharp edge to split pairs, do it with your fingers or/and a matchstick or small Phillip head screwdriver as a leaver.

Works so far but won’t stay in without tape on both ends of cable. Will be looking for a replacement.

I was upgrading my husband's computer to include a much beefier video card, and the multiple fans and their enclosure on it made plugging the large molded plastic plug for the front USB ports impossible. Ordered this and it was low enough profile to sneak in under the fan enclosure and gave him the use of those front USB ports back.