DC 12V-15V 25W~30W Subwoofer Amplifier Board Mini HiFi Class D Mono Channel

My new surround sound system requires a active subwoofer, however my nice sub is passive. Got this item and hooked it up and was originally disappointed due to lackluster performance and it making the sub sound as if it were blown at higher volumes. This was simply a power supply problem. I was using a 12v 1amp PSU. located a 12v 2.5amp PSU and the audio distortion went away. Eventually bought a 15v 5amp PSU and the sound is amazing. I soldered leads for the input directly to the board and then just mounted the board to the side of my desk for easy access to adjust the volume late at night without having to adjust anything on the decoder.

Worked fine for me used old 12v 1.2A netgear power brick. I did solder in an RCA pigtail in the pads next to the phone jack as my amp has an RCA output for a owered subwoofer and hooked it up to an old unpowered subwoofer this worked great. would probably work ok in a car as well. Very pleased with it so far

This is an incredible board for the price. It ran two 15w shaker subs like I needed. The only down side I found was the DC power jack does not work. This is because they connected pin 3 (the connection detect pin) of the jack to the ground plain instead of pin 2. I had to solder a jumper wire between pins 2 and 3 in order to get the jack working.

First I want to explain what I purchased this small amp to do... We have a camper that I replaced the stereo head unit in. The new unit does not have speaker level output for the subwoofer. However, it does have a line level out for a sub. We do not go to a campground to shake rattle and roll. So I did not need nor want a powerful system, just one that would add a little bass to the sound. Therefore, wattage wise, this one would be sufficient. I connected the unit to the sub (5" 4 ohm) and powered the amp via the house ~13.5 vdc. The amp cam on as it should and the sub began playing as it should while I adjusted the volume of the amp. I let it play for a couple of minutes, and went into the system EQ to make some adjustments to the sound. While it did not sound fantastic, I was not upset with it either. Just wanted to make some adjustments. About 10 minutes into playing, the bass suddenly stopped. I turned the entire system off then back on with the same result. I did that again, this time leaving it off for several minutes. When I turned it back on, it was with the same result as before. The stereo was working. It had sound coming from each speaker...except the subwoofer. I confirmed that this amp still had power, still had a signal, and was still connected to the subwoofer speaker itself. All those tests passed. I tried changing outputs coming from the stereo system...still nothing came out of the subwoofer. So all in all, it worked almost long enough to adjust the EQ in my system. The thing is, as I said to start with, I was not looking for anything GREAT. I just wanted it to work. I can not recommend something that only works for a few minutes. I am glad it quit before I drilled holes and mounted it.

Both ic's are rated for 18vdc. Wonder if i can push 17? Speakers pop when turned on and off maybe its the bt module. Using 12.5vdc. I would like it to be able to be switched on and off from the volume control. No on/off switch on unit. I made my own by removing the power port and installing a toggle switch. Sounds good. Sub crossover is normal.

Purchased it to power a passive subwoofer from an old Sony surround-sound system. Found an old 12 VDC power supply, cut off the male end and wired it right in! Wired up the sub, plugged in the headphone jack from the computer and I'm good to go!

I can not get this amp to perform properly no matter what I try. It is muddy and distorted at all volume levels. Speaker is good, the power supply is 15V 0-10A, source is good, wiring, enclosure... everything checks out except the amp. I give up. This thing sucks.

Works