Sharkoon QB One Itx PC Case

It's perfect case for a SFF build which supports full size GPU and ATX power supply. The build quality was great and elegant look with all removable side panels was nice. The main difficulty I was faced is that i had to reomve the hard drive mount bracket to put my Strix 1070 Ti because it is blocking the way and hard to insert the GPU having it. 2 fan GPUs can insert easily but for 3 fan GPUs you have to do some adjustments. But it can fit a full size GPU. The main con of this case is theirs no grills on the bottom of the side panels to exhaust hot air from GPU.So i'm planning to drill some halls on the two sides of the GPU area. Other than that its is the most compacted (13.8 L) case I found with support of full size GPU and PSU.

This is a reasonable ITX case which takes an ATX PSU and quite long GPU. I was able to fit a 650W PSU, Ryzen 5 3600 with Radeon RX5700XT graphics. It makes for a very compact but very capable mid-range gaming PC. The Good: Relatively well built for the price. Quite nice looking (When you remove the plastic "Sharkoon" badge!) I was able to fit a 290mm long GPU. I was able to fit a relatively inexpensive standard ATX PSU. I was able to fit a tall 90mm tower cooler. Some smaller 120mm coolers would also fit I think. Good ventilation with lots of grilles and mesh. Easy to work on for a small form factor case. Panels are removable off all 2 sides and the mesh front plastic moulding also removes. Access to the rear of the motherboard once fitted is good. I was able to change the cooler mount bracket without taking the motherboard out. The case can be orientated in both dimensions (short & fat or Tall and not so fat). Simply stick the supplied rubber feet to the side you want to have at the bottom. The Bad: The PSU needs to be a small (i.e. early ATX standard size) type. Extended size and most modular PSU's will NOT fit. This rules out most high quality PSU's over 600W. The PSU is mounted at the front so you only get an IEC socket at the rear, no power switch or access to PSU's power switch. The cables for the USB, Audio and LED front panel are way too long. It looks like they used standard length ones off a standard case. You have to find somewhere to wrap up and hide the excess. A 3.5" HDD is mounted in a stupid bulky plastic sled thing which wastes space. It is not hot swappable so I cannot see the point in the sled. There are mounting holes on the top for a 120mm AIO radiator, however if you fit a 3.5" in it's sled it will not fit. The Ugly: The nasty plastic Sharkoon badge. Fortunately it is only stuck on with double sided tape and is easily removed leaving no marks. The electricity arcing as you plug the power cable in as there is no power switch. Generally though if you need to fit a GPU longer then 270mm it is a good budget option. If your GPU is smaller than 270mm I would recommend the Silverstone SG13 instead. It is better built, smaller and supports modular PSU's for the same price.

Love this case. Every panel comes off. The cpu has tonnes of room. No rad room but the design is really clever. There is room for non modular psu cables that you don't use down the side ir extra room for an ssd down there or on the top of the psu or even an extra 3.5 hdd. Awesome. Board om this scale generally only have 2 ram slots and I found this case pushed my antek psu too close to the ram and it called for some very uncomfortable cable bending. The gpu however is my favourite thing. Rear exhaust gpus are perfect for this. The heat comes in the side (ehoch can be easily opened or the dust filters can be ripped off ) and is launched out the back. Obvious this isn't so good for fans that blow straight down onto the card like a sapphire r7 260x but the space is so tight that air flows nicely out the back anyway. Kinda reminds me of a console. Build quality is awesome. Small fans could even be shoved in the front and top and rear. But in a build this small with small gpus you probably only need a heat sync because most cpus this size don't run hot at all. my psu in this case was a 550w atx so I'm very happy with that. Antek true power 80 plus

Case comes with one 12cm fan installed. This fan is very quiet even when directly connected to the 12V, so I decided to use it without PWM. It acts as side intake. I decided to place case it in vertical position as PSU was generating alot of heat and hard drives temperature started to rise. Anyway, I was able to fit these components inside: - Corsair SF600 Full Modular Cable Management Power Supply, 80 Plus Platinum, 600 W; - Corsair Vengeance LPX 16 GB (2x8GB kit); - Gigabyte GA-B450I-AORUS-PRO-WIFI; - AMD Ryzen 7 2700 CPU; - ARCTIC Freezer 33 eSports Edition; - Sapphire Radeon Nitro + RX 580 8GB GDDR5; - Noctua NF-A8 PWM; - Three 2.5" hard drives. I've provided several images of assembled case. I have tested system stability with Aida64. CPU never goes over 63 degC, VRM goes to 72 degC and GPU goes to 77 degC. I could make it even with SF450 PSU, but from my experience, it is always better to have more "juice".

A very good case considering how small and cheap it is. The one downside was, although it was supposed to fit 240 AIO water cooler, in reality you couldn't close the top panel based on where the holes were (fans/cooler is mounted to top panel). I ended up drilling a couple of extra holes in there and moved it 1 cm down, and it opens/closes perfectly.

Ce boitier fait environ la taille d'un bagage à main de compagnie aérienne, pratique pour le garder avec soit dans l'avion, ce qui était déterminant dans mon cas. Je devais travailler à l'étranger avec un ordinateur puissant, c'est une alternative aux pc portables, il est autrement performant, silencieux et également beaucoup moins cher qu'un pc portable de même capacité. Comme tous les boitiers de petite taille, il faut bien choisir ses composants afin que tout rentre parfaitement et qu'il soit correctement aéré. J'ai utilisé une carte mère format ITX, une alimentation format SFX modulaire gold ( histoire de ne pas être embêté par les câbles), un ssd en m2 avec dissipateur thermique, 2 ssd en sata, le processeur est un ryzen 7 5700x, 2 x 32 gb de ram en 3200 Mhz, un ventilateur de cpu Noctua NH-U9S et 3 ventilateurs de chassis Noctua en extraction d'air. La carte graphique rtx 4060 est de format court, donc aucun problème d'installation. Le tout fonctionne très bien sous un format compact et en silence tant que la machine n'est pas utilisée pour des charges lourdes de calcul prolongé, dans ce cas, le bruit reste très supportable. S'il fallait chicaner, pas de de prise usb c en façade.

Plenty of options for cooling. Dust proofing is good.

Använder detta chassi som server. Mycket snygg och lätt att komma åt för installation av ITX-moderkort. Det finns plats för 2 st 3,5" hårddiskar och 1 st 2,5" SSD. En fläkt som kyler och den är mycket tyst.

Puntos interesantes: - Relativamente barata. - Tamaño muy pequeño, sólo un poco más pequeño que una Silverstone SUGO SG-05 y más pequeño que la gran mayoría de cajas ITX. Ideal para HTPC. - Posibilidad de montar 2 unidades de 3.5" y 1 de 2.5" (lo normal en este tamaño es 1 y 1, como en la propia Silverstone). - Compatibilidad con fuentes ATX (en mi caso he usado una SFX). - Compatibilidad con gráficas de PCI de hasta 2 slots y más de 25 cm (en mi caso una GTX 1660 Super, entra sin problema). - Compatibilidad con disipadores altos (no muchas cajas ITX permiten ¡150! mm de altura en el disipador). Lo tengo montado con un Noctua NH-L12 de 90 mm, pero estoy seguro que un NH-L9 de 120 mm entraría sin problema. - Bastante espacio para montar (para una caja ITX tan pequeña). Puntos a mejorar: - Falta un ventilador frontal, y más si es grande. (No hay hueco para ponerlo, además). Es difícil diseñar un circuito de aire con un ventilador trasero y dos superiores (la caja incluye uno superior de 120mm).

Sembra un case di ottima fattura. Ottimo per le build piccole. Nel mio caso do dovuto fare il reso perché non supportava le componenti scelte.