AquaTru Under Sink Alkaline RO Water Purifier | Certified 4-Stage Ultra Reverse Osmosis Removes 84 Contaminants Including Forever Chemicals, Lead & Fluoride | Adds Minerals | High-Capacity with Faucet

I always had a whole house carbon block filter in my houses, but this takes clean water to a new level. I run 2 ice makers and the one sink faucet supplied. I added another 5 gallon tank in parallel to the supplied tank so I would not run low on the RO water when filling pots of water for cooking, etc.. Using two tanks actually improves the water pressure at the sink faucet. Was easy to install. I put it in the basement below the sink area so the unit did take up cabinet space.

This is the 2nd. one that I have had. Seems legit me every 6 months or so the system pressure drops and it trickles and I have had problems with the lines leaking. Call company and they replaced the first one and here we are again and no response! This cost to much to have so many problems and then to be ignored.

Easy to install, however like others have said, the connectors are prone to leaking. It didn’t leak at first however it started to after about a day or two of use. Easy fixes, had to tighten a few connections. The worse one being where the line connected to the actual faucet.

Wonderful filter system. I have always liked water but I love it more!

I've installed 2 of the under sink models in the last 6 months. Both had initial leaks, 4 of them in total. First was the sanitizer attachment to the holding tank. I reinstalled with more turns, thinking initially I had not tightened enough, still leaked, reinstalled for a third time, somewhere in the middle, that has worked so far(6 months). Note the outlet ends up wherever, as loosening or tightening to match the instructions led to leaks for me. I used 8-10 revolutions of the provided teflon tape each time. I don't think the tape does anything. The seal is provideded by the rubber gaskets. 2nd was a leak where the RO tank valve attaches to the sanitizer. Tightened a 1/8 turn, leak stopped. May be operator error, but it's tighter than I would normally put on this type of rubber gasket seal. Again, It ends up pointing wherever, seems much to finicky to adjust so it points down as the manual shows. 3rd was total operator error. The sanitizer cap. Be sure to tighten completely until you reach the positive stop. 4th...Where the quick connect fitting attaches to the faucet. Reinstalled the clear plastic washer multiple times, still leaked, a lot, not a subtle drip. In desperation I tried using one of the black washers left over from the cold tap water adapter package. I think this was to support a 1/2 supply line. That worked first time. I can't see anything wrong with the clear plastic washer and it seemed to fit into the quick connect fitting just fine. Weird I've done quite a bit of DIY plumbing in the last 50 years. I've learned that these rubber gasket type fittings do NOT need to be that tight. Not true for some of these fittings. The tubing behind the filter manifold is not contained in the cavity, tubes are thicker by about 3/8 inch. So the manifold will not hang vertical if you tighten the mounting screws down to lock the manifold in place. I just left the screws out 1/4 inch. The tubes are resting against the wall though, not the best, but doubt it will be an issue. When installing the 1/4 inch tubing to the cold water adapter be sure to force the tubing over the ridge until it hits the stop. Takes a fair amount of force. I put some silicone lubricant on the fitting which seemed to help. No where in the manual does it explain how to operate, or better yet, how the system operates. It goes from installation to maintenance. I realize there is nothing to do really, but a few words on what to expect would be helpful. Note, no water will come out for several minutes initially. Expect some serious spraying as the air gets out of the system during the first 2 tank fill cycles. The manual states a tip to use the drill bit to align the drain saddle while tightening it down. Do not use the 1/4in bit you drilled the hole with. This will damage the quick connect internals if you push it thru. Use a drill be about half the diameter to avoid this. I had to read the sanitization section to find out it can take up to 2hrs for the tank to fill. Since there is no electricity to the unit, no display, which I think is a good thing. The only way to know it's working is to listen carefully for the waste water draining. The leaks at install have me concerned about the long term. However after one unit running for 5months It's worked 100% as advertised. Hope it stays that way.

Really love Our system! The water tastes great. Knowing that the Family & I are drinking healthy & mineral-enriched water is a comfort every time I fill up. The filter systems side wall mount fits great under our sink. Very happy!!

Two parts are low quality, keep leaking. Please send me the two replacements. Updated: refund is completed.

Muy buena calidad