Saker Chisel Sharpening Jig,Wood Honing Guide with Whetstone - Red Off-Center Upgraded Honing Tool and Diamond Sharpening Stone Set Kit for Knife, Short Chisels and Planes

Purchased to aid in sharpening hand plane irons, and wood chisels. I swap between hand sharpening and using a fixture to keep the bevels in line. What you need to know, the fixture seems built well enough for the price point. It uses the shank of the chisel to set the horizontal plane. Meaning, if your chisels are not square or flat down the shank it will sharpen an odd angle on the tip. This may or may not be a problem for your application. Used carefully, and on good chisels and plane irons it will work fine. Cant speak to the diamond stone, havent used that much. I have my own stones.

After years of poor planing I researched this and was pleasantly surprised. It comes with two sharpening surfaces, and the attaching roller makes for a consistent flush and sharp edge. It can be a bit tricky getting the face perfectly flat on the stone, however the tool comes with a measurement guide that does help. After the first few strokes it can easily be adjusted and the result is great. I also use it on my wood chisels as well.

Got this to straighten out my woodworking tools. Consistency is beyond anything I could do free-hand, especially on something like a 6mm chisel where it's really difficult to feel a face registering flat. From flattening on 80-grit sandpaper all the way up to a 6000-grit water-stone for a mirror-polish, you can literally read text in the reflection, and it's dead flat; no waviness on the edges that sometimes happens free-handing it. I flatten all the faces then put it in the guide and begin back at the bottom of the grit ladder, 80 or 150 to flatten, then 1000-grit water stone and 6000 to polish. To be fair, to completely re-face the 1" chisel by hand took probably 2-3 hours and 5-6 sheets of 80-grit. It can be done with the honing guide if you have the patience. Once it's flat, it takes maybe 20-30 minutes on the 1000-grit just cause I skip a lot of grits in between; (only had low-grit paper and two-sided water-stone). Then 10-15 minutes maybe on the 6000-grit for a mirror polish, depends on the size of the chisel too. That's all for a full-reface though, once it's done, it's much faster to do touch ups on a secondary 30 degree bevel after the 25 degree has been established. In that 3 hours, the chisel didn't move once after it was locked into the guide, only thumb-tightened. It doesn't required much pressure if you let the grit do the work. If you really put weight into it, it might slip but muscle is unnecessary imo Would recommend that you go through all the grits in one go after setting the chisel in the guide. There's no real way to set the chisel exactly back in the spot where it was if you mess with it in between grits. You can get close but we're talking a couple microns for dead flat mirror polish and if you tweak it in between you'll throw off the alignment. You'll notice your polish line will be ever so slightly higher or lower if you mess with it in between. Might not be a big deal depending but something to note If you're going to use it on slab+low-grit, it helps to put a piece of tape or paper down to protect the roller. On a polishing stone, it mostly just glides without damaging the face of the roller. Oiled the bearings regularly, idk if they'll rust from being used on a water-stone; looks like the pin can be hammered out so if they need to be cleaned or replaced should be easy enough For me, it fit a 6mm chisel, all the way up to a 2" plane blade. A minor issue is the roller is so closely machined to the body that it can accumulate lint/metal shavings in between the body and the roller. It's easy enough to dust out but with a little more clearance is probably avoidable altogether. Only wish there was a jig included to set degrees, like made of plastic or such. I'm definitely going to ruin the instruction sheet with the reference markings on it, so will have to make my own jig for 25 and 30 degrees before I lose the instruction sheet. Small issues aside, it works very well so far. Can't comment on longevity. Hopefully it'll last cause I can see this being one of those 'if it goes missing I'd buy it again immediately' items. Do not even want to attempt free-handing small chisels again after seeing how accurate a sharpening jig really is.

Works well, grips the blade securely, easy to set the desired angle. Simple tool but does it’s job well.

I initially bought this because it was the cheapest among the ones I looked at. Now that I've used it for a while I think it was a good decision beyond pricing. First, I can see how the single wide wheel is an advantage over those I was looking at with two wheels placed towards the outside edges. The "mono" wheel allows you to sharpen right up to the edge of the stone without tipping or having a wheel fall off the edge. It rolls smoothly and true, seems to be wearing well and I noticed that there are bearings inserted into each side of the wheel. I put considerable pressure on it and the axle remained strong. The first thing I sharpened was an old, very short, chisel. When I inserted it into the guide I could not achieve the proper angle because of the length of the chisel. I then realized I could just turn it around and with the offset roller get the proper angle. The clamping mechanism works well also. I had little to no slippage of the tool, which was a concern at first, but I did stop periodically to re-tighten just in case. It brought my old rounded and out of square chisel back to a nice straight and sharp condition. I recommend it confidently.

It's a standard sharpening system. I'm sure it works as well as any other. I received a box that appeared to be a return, but it may just have been crushed at the warehouse. It was heavily taped together. Inside it, I found all the items that should have been there, plus a few others. Since I got some stray parts, I have to guess it was crushed along with other products and then repacked incorrectly. The first picture shows a probe of some kind. A tag says to wear gloves when removing it so I presume it heats up. The second and third pictures show a leather something or other. It has two hooks at the bottom. I could use it to hold a small picture frame. Whatever these things are is beyond me. I'll be tossing the probe, but the leather thing interests me. I didn't take off any stars because the sharpening kit was complete, but whoever orders the products that include that probe and that leather thingie are going to be taking off stars.

this works as advertized but it has a hard time to get the angle right on short chisels .

The first package that arrived was missing the guide and the instruction sheet, and Amazon took just 2 days to ship a replacement. With the guide and the sharpening stones, It is quite easy to restore my old chisel with this set. I am giving this product only 4 stars, because the instruction sheet is tiny. There is a small scale printed on the paper which one uses to set up the angle of the blade. I wonder how long that piece of paper will last.

I have a fair few chisels which over time I've just thrown in a tool bag and the blades have dulled to make them pretty much useless. I bought this as I could do with sharpening up some blades instead of buying new chisels. I wasn't expecting to be able to get them super sharp considering the state of them It took a long time but the results are great. I would recommend using a bench grinder to get any chips out of the edge but this does a good job putting a nice cutting edge back on my chisels. The guide is easy to use and super sturdy too. The stone seems to take material off quite well although I would like to see a higher grit included in addition to 400 and 1000 as I think I could easily get a mirrored edge with a bit of elbow grease. You can see the state of the chisel I used in the picture and I think the edge has come up pretty well. You can see score marks from the stone so I will look for a new stone with a smoother finish to get my blades as sharp as possible. Overall, a great investment to keep chisels and blades sharp

Well engineered, grips the blade well every time, smooth rolling action. Would recommend.

+ Die Verarbeitung ist sehr gut + Es lassen sich einfach sehr gute Ergebnisse erzielen + Die Laufrolle läuft gut und liegt durch ihre Breite sehr stabil auf + Von kleinen Stechbeiteln (6mm) bis zu Hobeleisen lässt sich alles einspannen - Die Halterung ist aus Aluminium, wodurch im Laufe der Zeit die Funktion nicht mehr ideal ist An sich eine super Erweiterung in meinem Schleifzubehör. Einmal eingestellt und schon kann jeder ein gutes Ergebnis erzielen, ohne lang nachzudenken oder Angst zu haben, etwas falsch zu machen. Für den Preis ist die Qualität sehr gut. Wer etwas noch Stabileres will, muss wohl einfach bereit sein, mehr zu zahlen.

Funciona tal y como se esperaba. El material es robusto y es muy fácil darle el ángulo deseado a los filos. Contiene una pequeña guia de papel donde te indica las medidas exactas y las posiciones para obtener los ángulos del filo deseados.

Buen producto afila muy bien y el accesorio para afilar formones o gurbias planas es muy cómodo