Comgrow 3D Printer Filament Dryer Box SH02, 3D Filament Memory, Keeps Filaments Dry During 3D Printing, Compatible with 1.75 mm/2.85 mm PLA PETG PC ABS ASA, Filament Dryer, Spool Holder

Love this. If you are a serious 3D printer using anything above PLA or PET-G, you need this. The high drying temperature is essential for filaments like ABS and ASA, and few dryers reach those highs, including the Bambu AMS/AMS2. I just use this offline and run for 12 hours and transfer to my AMS when I need it. Two separate compartments means I can run things like PET-G and ABS at the same time for optimum humidity. It's a steal at the price.

Love this product, I always keep a spool of it as my go to filament for reliability and quality product, never have any problems , adhesion to build plate is excellent ( creality mag bed) i dont use any products to aid adhesion , the quality of the print is great with a nice shiney appearance and colour is uniform, cost is good although a touch more expensive than some filaments I have used ( usually Basicfil) iyts worth it as you know your going to get a good finished product. Thoroughly recommended.

As a beginner to 3D printing the first filament I bought from another company didn't work on my Labists X1 (seems it needed over 200 degrees to extrude)...I was hoping this would be different and it worked straight away! I printed an echo dot holder successfully which I've been using since. I can't compare it to other spools as this is the first one I bought (which works) other a short multi coloured set for 3d pens which wasn't ideal for for prints requiring over 15 meters. What I can say is that it is nicely spooled (not tangling anywhere) and very even throughout.

I purchased this mainly as a drying box, It does the job and the controls are pretty straight forward. It would have been nice had there been a sealing gasket where the lid meets the base as this would provide a much more efficient seal. It performs the task required of it and enables me to prep the filament prior to printing. It's pretty basic but suitable for the demands of most filament. I have an AMS 2 which can also dry the filament but only when no filament is loaded into the gear mechanism and not during printing. At this price point you expect products to be a bit plasticy and this unit continues that tradition.

Upgraded to this after purchasing a single reel filament drier and always being stuck on preparing the next filament. Honestly haven't looked back or needed anything more, it did exactly what is meant to, easy to use, nice compact size, keeps my active reel dry and preps the next one whilst im printing and love that it displays the temp and humidity. Came quickly and packaged well and been using it for months now without issue. Cheap and cheerful!

Really happy works well for pa6-cf20

After leaving a a dissatisfied review on their PLA Comgrow got in touch regarding my review ( didnt expect them to) and after a lot of communication between them and I we came to an amicable agreement. I have now started printing with their PLA even though I was hesitant to do so but I`m now one hour in on a 3hr print and I have to say the product is extruding well and adhearing to the print surface. So two big thumbs up to Comgrow 3D for customer service and discussing the issue with me. Would buy again, but also not that there will be from time to time products that slip through the net I understand this but their customer service more than made up for this. Well done Comgrow 3D

I have used this PLA a few times before in white. I've had a few problems with blocking and uneven prints with the white. The last one I bought was grey. I tried several times to print, but failed every time with poor bed adhesion and lumpy filament laying. The quality is simply awful. It's almost as if there were none melted lumps in the printed lines! I have an Ender printer which I've used for many print jobs without issue. I then bought a role of proper Ender PLA filament and it printed like a dream! Obviously the cause of my print failures was this make of PLA. My advice, spend a bit more and get a quality filament. This product is not fit for purpose.

Auf dem Ender 3 V2 unschlagbar gut. Perfekte Haftung und Druckqualität auch mit Default Einstellungen des Druckers.

Llego en perfecto estado, pero el producto llego abierto, la etiqueta de sellado había sido retirada, pero supongo que fue por el el proceso de aduanas ya que fue un producto de importación, de todas formas al revisar el producto que es lo importante parece ser que todo está en orden y que los filamentos aún conservan su empaque al vacío, más adelante actualizare sobre el desempeño de los filamentos ya que no he tenido tiempo de probarlo

Das PLA ist perfekt auf die Spule gewickelt, keine Schlaufen etc. Druckt problemlos bei 200 - 210 Grad und haftet einwandfrei auf dem Druckbett (ohne Heizbett, nur mit Malerkrepp). Dazu preislich attraktiv. Empfehlenswert.

El bobinado no da ningún problema. Se imprime perfectamente, he comprado varios y el negro es el que encuentro que se pega mejor a la base. Ni atascos ni problemas de configuracion para el material imprimo a 195° y 60° para la base.

Preso su warehouse ad una cifra ottima, arrivato senza scatola e senza sacchetto per l'umidità quindi mi aspettavo grossi problemi in stampa invece... Un ottimo filamento, non fa bolle e bobinato bene ed ha un bel colore. Quindi prodotto veramente buono ma a questo giro la spedizione è stata preparata veramente male...