AMD Wraith Prism LED RGB Cooler Fan from Ryzen 7 2700X Processor AM4/AM2/AM3/AM3+ 4-Pin Connector Copper Base/Alum Heat Sink, compatible with Desktop

Works well in Dell Studio XPS 7100. This unit happens to have a USB2 header free by design, to power the RGB. They provide in the box a 4pin to RGB Gen1, and USB2 Header to 3pin cables. There are nice rubber covers for the two ports (3pin/4pin) side by side on the clamp opposite face. on the opposite end of that side of the fan is a H/L fan speed switch. That switch just raises the max rpm ceiling of the cooler an additional 550-600 rpm. The temperatures are overall lower on the cores. Comes with pre-applied thermal grease patch. Extremely quiet, even on this primitive PWN Dell Cool n Quiet system. This is the Phenom II 1090T (AM3 Socket). Excellent cooler. The RGB is awesome, but this machine from 2011 is a little before glass panels lol I also modded a 120mm fan in front of case, but that is a different topic. Great CPU cooler.

Works well. It isnt too noisy at all and Im happy with the product so far. It was a good buy for the money. It wasnt too big. Its OEM quality

This cooler runs my 1600AF chip at 25 degrees C at idle. I know, when I was a child in America my teachers taught us the decimal system and promised us that when we were their ages, the US would have standardized the Metric system. Four pin Fan power and then optional connectors 4Pin ARGB or 3 pin to USB header. The 4 FAN is hard wired in and the two ARGB or USB header (9 pin USB 2.0) are optional to provide the illumination and control. Great temps, limited RGB options but one is the TEMP setting, 1 of about a dozen. As you can see in the pic is idling green. Very pleased. This item was purchased from a return stock and was scratched up pretty good. Windex Vinegar, a paper towel and 5 minutes results in it looking new. The face of the sink was also dirty with old compound. Alcohol pads I use to clean my readers, perhaps 5 in total and some work and it came near new clean before installation. Very happy with it. So this is my 2cents on installation. I aligned mine so AMD could be read in the upper left side, assuming this was the intended orientation of the fan. This means the lock side is near the top of the board. I clipped the bottom ring on the AM4 plastic mount first and made sure the top side clip was in the extreme 'relaxed' position that is the latch allowing the clip to travel towards the board as much as it allows (play with a minute, get familiar). Then once the bottom was clipped on I sat the sink level and pushed (gently) while apply pressure on the top near the base where the square clip is moving it side to side slightly to align the hole with the plastic catch, I pushed harder on the metal clip than I did on the sink to avail the 'click' of the second clip. Once done, move the clip lever (black) at the top over to face the other direction, 'locking' the heat sink in place. This is a wonky procedure, but is not really all that hard.

I picked up this CPU cooler for a PC CPU upgrade I picked up from Ebay. I paired it with an AMD FX-8370E Works really well. I like the slow and high control on it and also like the RGB it has which can be changed or controlled with a few programs. Pretty quiet on high setting and if aren't a gamer the low or with Qfan enabled its super quiet. Temps say around 30c idle and only see 50c when gaming with high settings. I also like that it came with the micro usb to usb to connect the lighting to my momo, being the one I'm using is older and doesn't have a RGB plug on the mobo. Very happy with this purchase.

After initially receiving the wrong part, ordered it again and got the correct one. Easy to install and works great. Pre installed thermal paste I don’t think was quite enough, but it’s pretty quiet all things considered, and the RGB is a nice touch

Used product but came in excellent condition with thermal paste, cables, etc. I removed the stock paste and added arctic silver but that’s about it! Does not come with mounting brackets but I already had them. Install was super easy - just plop down and secure the clips and you’re off and running. Colors look awesome and runs cool - I’m under 40C on a 5700G browsing, watching videos, etc.

Muy bueno. Silencioso y cumplidor.

everything I was hoping for when I received the product. the only difficult part was USPS delivered it to the wrong address.

E' perfetto, tiene basse le temperature ed è silenzioso

Top Lüfter von AMD, einfach zu installieren und beim Anschluss über ein internes USB Kabel und der AMD Wraith Software viele Spielmöglichkeiten bei den Einstellungen der Effekte. Die CPU wird im High Modus gut runtergekühlt und ist auch leise.

This cpu cooling fan has been made by cpu manufacturer AMD and makes fitting a breeze as there are no after market adapters it just clip straight in. The LED'S look great too.

自作PCに付けたくて買いました。取り付けを事前に確認してなかった為焦りましたが、問題なく装着。買って良かった。迷ったら買いましょう！

.